Creative machines

Wall Plotter

An A2 wall plotter that feels the pen and sees the ink

WP-01 hangs a pen head from two Dyneema cords and draws on A2 sheets on your wall. A load cell holds the pen force constant and a camera checks the line: when the ink runs out, it pauses and redraws from the last good point.

  • In development
  • Level: Advanced
  • Version: 0.1.0

v0.1.0 first design: simulated and unit-tested, not built yet. Performance numbers are estimates.

The experience

You print 27 of the 31 made parts, bolt two motor pods to a 2020 beam and hang the board on your wall with a 6° lean. Wind the Dyneema cords, balance the head, flash the CoreS3 and the head camera node, then run the calibration steps. In PlotStudio you turn an image into lines, hatching or stippling and watch a realistic simulation before any ink touches paper. Upload the job and the plotter runs from its own storage, holding the pen force you set and watching the line it draws. Along the way you learn cord kinematics, motion planning and force control. This is a first design: simulated and unit-tested, not built yet.

What makes it special

Constant pen force

A load cell in the pen clamp and a servo-preloaded spring hold the tip force at the pen's value, 5–80 gf (design range).

Camera ink check

A camera on the head watches the line behind the tip. INK OUT pauses, parks the head for a pen change and redraws from the last good point.

Six drawing styles

Lines, Hatch, Orthogonal, Stipple, Spiral and TSP art. Each layer of a job has its own style and its own pen profile.

Simulate before plotting

PlotStudio renders each pen's width, colour and layering, animates the plot and estimates the time with a port of the firmware planner.

Never lose a drawing

Ink out, a lost head link, a pause or a power cut all resume from a known point of the job. Jobs run from the plotter's own storage.

Mech livery

Graphite body, white armor plates with yellow inlays printed in two colours, and a mech HUD on the CoreS3 touch screen.

What you will learn

  • V-plotter kinematics: pulley wrap, cord stretch, resolution
  • Statics: cord tensions, the safe zone and motor torque
  • Motion planning: junction deviation, look-ahead, trapezoids
  • Force control: series-elastic actuation and a load-cell loop
  • Machine vision: homography, contrast profiles, ink coverage
  • From images to paths: hatching, Voronoi stippling, TSP ordering
  • Pens and paper: force, speed, bleed and layering

Three ways to get it

Be the first to build the Wall Plotter

This kit is still in development. Leave your contact and we will write to you when it is released.

DIY: files and software

The whole build is yours: print the parts, buy the components, build the electronics and assemble the machine.

You do
Print, source the components, build the boards, assemble
  • Print files of every part (STL, STEP and 3MF)
  • Electronics design: wiring, schematics and the list of components
  • Firmware and software, including the app when the kit has one
  • Assembly manual
Notify me

Kit: electronics ready

The hard part comes done: every component, with the electronics assembled and tested. You print the parts and put the machine together.

You do
Print the parts and assemble
  • Everything in the DIY option
  • Every component on the bill of materials: electronics, cables and hardware
  • Electronics assembled and tested, ready to connect
  • Filament not included: you print the parts
Notify me

Ready to use

Printed, assembled and tested by us. Install the software and start using it.

You do
Install the software and use it
  • The complete machine, printed and assembled
  • Tested before it leaves the workshop
  • Firmware installed; app, manual and files included
Notify me

Price on request: it depends on the option. In the DIY option the filament, the electronics and the hardware are yours to source (this page lists them); in the kit option, only the filament.

Included with every option

The files, the manual and the software come with every option, the ready-to-use machine too.

Print files

  • STL files for every printed part, with pen adapters for Ø7–20 mm pens
  • Two-colour 3MF files for the armor plates with the mech livery
  • STEP assembly and STEP parts for CAD
  • DXF for the laser-cut steel ballast ring
  • Firmware for the CoreS3 controller and the AtomS3R-M12 head node

Assembly manual

  • Build guide with every part and step, from the frame to winding the cords
  • Bill of materials and the wiring diagram
  • Calibration guide: dock, head balance, load cell, geometry, camera
  • User guide: from an image to a finished A2 plot
  • Seven-chapter theory course with 18 figures, plus a kinematics study

App

PlotStudio Windows

  • Open an image or SVG and build layers, each a style with its own pen
  • Realistic preview, plot animation, time and ink estimates
  • Pen library with profiles and test strips
  • Connect over USB, Wi-Fi or the built-in simulator; jog, live force chart, head camera
  • Calibration wizards and every controller and head parameter
  • Upload, start, resume and follow jobs live