Control & robotics

Four Legs Robot

Twelve servos, five gaits and a robot that decides for itself

A didactic quadruped with twelve servos, built to learn how four-legged animals walk. Its design includes five gaits you can change while it walks, an IMU that levels the body, a camera that finds free floor on board and GPS waypoint missions, all watched from a Windows app.

  • In development
  • Level: Advanced
  • Version: 0.1.0

Design v0.1.0: simulated and checked in CAD; the first unit is not built yet

The experience

Start in GaitStudio's simulator: press STAND and WALK, switch between walk, trot, pace and bound, and watch the footfall diagram, the support polygon and the stability margin change. Then print the 48 PETG parts and the TPU feet, fit twelve DS3218MG servos with the calibration jigs, and stack the CoreS3 on its servo module with the camera in the head. Lay the robot on its belly and press STAND: it is designed to rise, walk under your commands, keep its body level on a slope and stop its autonomous modes when the vision goes stale. Pose the body with the feet planted to see inverse kinematics at work, send it on a GPS mission, and read the twelve-chapter course in the LEARN tab.

What makes it special

Five gaits, live

WALK, TROT, PACE, BOUND and CUSTOM: change the duty factor, phase offsets, step height or body sway from GaitStudio while the robot walks.

Three joints per leg

Abduction, hip and knee, each backed by a 625ZZ bearing. The knee is driven through a parallelogram four-bar so its servo sits near the hip.

Vision in the head

An AtomS3R-M12 learns what the floor looks like, finds where it ends in every frame and sends 16 free-space sectors to the brain.

GPS waypoint missions

Waypoint missions and return-home, with gait odometry fused with the GPS, and obstacle avoidance from the camera and a ToF sensor.

Autonomous and safe

The robot decides on board. Hardware E-stop, fall detection, battery and servo-rail monitors: losing the PC never makes it unsafe.

Simulator with real code

GaitStudio runs a line-by-line C# port of the gait engine, filters, navigator and supervisor, with noisy sensors and a synthetic camera.

What you will learn

  • How animals walk: gaits, footfall diagrams, duty factor
  • Forward and inverse kinematics of a 3-DOF leg
  • Body kinematics: moving the body with the feet planted
  • Gait generation: phase oscillators and foot trajectories
  • Stability: support polygon, static margin and ZMP
  • Attitude and heading with complementary filters
  • GPS navigation, odometry fusion and waypoints
  • Vision, free-space detection and obstacle avoidance

Three ways to get it

Be the first to build the Four Legs Robot

This kit is still in development. Leave your contact and we will write to you when it is released.

DIY: files and software

The whole build is yours: print the parts, buy the components, build the electronics and assemble the machine.

You do
Print, source the components, build the boards, assemble
  • Print files of every part (STL, STEP and 3MF)
  • Electronics design: wiring, schematics and the list of components
  • Firmware and software, including the app when the kit has one
  • Assembly manual
Notify me

Kit: electronics ready

The hard part comes done: every component, with the electronics assembled and tested. You print the parts and put the machine together.

You do
Print the parts and assemble
  • Everything in the DIY option
  • Every component on the bill of materials: electronics, cables and hardware
  • Electronics assembled and tested, ready to connect
  • Filament not included: you print the parts
Notify me

Ready to use

Printed, assembled and tested by us. Install the software and start using it.

You do
Install the software and use it
  • The complete machine, printed and assembled
  • Tested before it leaves the workshop
  • Firmware installed; app, manual and files included
Notify me

Price on request: it depends on the option. In the DIY option the filament, the electronics and the hardware are yours to source (this page lists them); in the kit option, only the filament.

Included with every option

The files, the manual and the software come with every option, the ready-to-use machine too.

Print files

  • STL files for every printed part, plus two calibration jigs
  • Five armor plates as two-colour 3MF with the yellow mech livery
  • STEP files for CAD
  • Firmware for the CoreS3 brain and for the AtomS3R-M12 camera

Assembly manual

  • Build guide with every part, fastener and step
  • Bill of materials and wiring diagram
  • Calibration guide: servo trims with the jig, IMU axes, magnetometer, camera geometry
  • 17 lab experiments
  • Safety notes and first power-up procedure

App

GaitStudio Windows

  • Camera view with the free-space sectors drawn on the floor, and a drive pad for mouse, keyboard or game controller
  • Live footfall diagram, leg views, support polygon and stability margin
  • Body pose sliders with a 3D twin, plus attitude, compass and sensor charts
  • GPS map with waypoints and missions
  • Every robot and camera parameter, servo calibration, Wi-Fi setup and CSV recording
  • Simulator and the LEARN tab with the whole theory course, offline