3D printing workshop

Filament Dryer

An insulated 2 or 4 spool dryer that controls humidity, not just heat

An insulated, 3D-printed filament dryer for 2 or 4 spools, run by an M5Stack Dial. It compares chamber and room humidity, vents only when venting removes water, and feeds the printer through one PTFE outlet per spool.

  • In development
  • Level: Advanced
  • Version: 0.1.0

v0.1.0 design: checked in CAD, firmware unit-tested. Not built yet; performance figures are estimates.

The experience

You print a chamfered frame, sandwich panels and white armor plates with yellow mech livery, all without supports on a 256 × 256 mm bed. Then you build a real appliance: 20 mm insulation, double-glazed doors, a PTC heater cassette with its fan and duct, spool rollers on 608 bearings and a 24 V supply in the base. You wire M5Stack units to a Dial, flash the firmware and start a preset from the ring, a phone browser or MQTT. Along the way you learn why absolute humidity decides when to vent, how PID control holds a temperature, and why a thermostat and a thermal fuse must protect the heater without any firmware. This is a first design release: checked in CAD, not built yet.

What makes it special

Humidity-driven venting

Two SHT40 sensors, chamber and fresh-air intake. The firmware compares absolute humidity (g/m³) and vents only while venting removes water.

Print from the dryer

Each spool rolls on two printed rollers with 608 bearings and feeds the printer through its own PTFE outlet on top.

Two sizes, same parts

FD-04 is two FD-02 modules in one chamber: same panels, doors, heater cassettes and cradles. Only the width rails and the base are longer.

Three over-temperature layers

A 95 °C thermostat and a 110 °C thermal fuse in series with each PTC element work without firmware. The firmware derates the heater from 80 °C at the outlet.

Dial, web and MQTT

Start presets on the M5Stack Dial, from a web dashboard on your phone or over MQTT with Home Assistant discovery. There is a JSON API too.

Truthful mech livery

White armor plates with yellow markings inlaid 0.6 mm as two-colour 3MF. The text (spools, volume, max temperature, power) comes from the model.

What you will learn

  • PID temperature control of a PTC heater
  • Absolute vs relative humidity, and when venting helps
  • Insulated sandwich walls and heat-loss estimates
  • Hardware safety that does not depend on firmware
  • I²C sensors and I/O on M5Stack units
  • MQTT and Home Assistant discovery
  • Two-colour printing with inlaid livery

Three ways to get it

Be the first to build the Filament Dryer

This kit is still in development. Leave your contact and we will write to you when it is released.

DIY: files and software

The whole build is yours: print the parts, buy the components, build the electronics and assemble the machine.

You do
Print, source the components, build the boards, assemble
  • Print files of every part (STL, STEP and 3MF)
  • Electronics design: wiring, schematics and the list of components
  • Firmware and software, including the app when the kit has one
  • Assembly manual
Notify me

Kit: electronics ready

The hard part comes done: every component, with the electronics assembled and tested. You print the parts and put the machine together.

You do
Print the parts and assemble
  • Everything in the DIY option
  • Every component on the bill of materials: electronics, cables and hardware
  • Electronics assembled and tested, ready to connect
  • Filament not included: you print the parts
Notify me

Ready to use

Printed, assembled and tested by us. Install the software and start using it.

You do
Install the software and use it
  • The complete machine, printed and assembled
  • Tested before it leaves the workshop
  • Firmware installed; app, manual and files included
Notify me

Price on request: it depends on the option. In the DIY option the filament, the electronics and the hardware are yours to source (this page lists them); in the kit option, only the filament.

Included with every option

The files, the manual and the software come with every option, the ready-to-use machine too.

Print files

  • STL for every printed part in its print pose, one set per variant (FD-02 and FD-04)
  • Two-colour 3MF files for the armor plates and the control plate, with the mech livery
  • DXF for the laser-cut parts: aluminium baffle and heater shelf, polycarbonate window panes
  • STEP of the full assembly and of every part
  • Firmware binary for the M5Stack Dial, ready to flash

Assembly manual

  • Build guide: part tables with sizes and materials, assembly steps, print settings and sourcing
  • Electronics: wiring diagram, pin map, power budget and bring-up steps
  • Firmware guide: states, presets, safety rules, Dial interface, web dashboard and JSON API
  • MQTT guide: topics, Home Assistant discovery and printer integration examples
  • Bill of materials per variant, mechanical notes with the thermal estimate, and a safety page

App

This kit works without an app.