Creative machines

Star Tracker

A printed turret that points your phone at any star and follows it

ST-01 is a 3D-printed alt-azimuth turret for your smartphone. Pick a star, planet or galaxy in the ST-01 Sky app and the mount turns the phone's camera to it and tracks it as the sky turns, while a laser pointer shows it to everyone around.

  • In development
  • Level: Advanced
  • Version: 0.1.0

v0.1.0 first design: tested in software, not built yet. Mechanical and electrical numbers are estimates.

The experience

You print 26 of the 28 made parts plus five armor plates, fit two pancake NEMA 17 steppers with GT2 6:1 belts, stack the CoreS3 on its driver module and screw the turret onto a tripod. Clamp your phone, connect over BLE and run ALIGN: the app levels with gravity, spins the turret to calibrate the compass against the motors' field, then you tap a star on the camera image to sync. Pick a target and the mount slews to it and tracks on its own while the app labels the sky. You learn celestial coordinates, sidereal time, mount models and laser safety interlocks. First design: tested in software, not built yet.

What makes it special

Point and track

The app sends RA/Dec; the mount converts it to motor steps 50 times a second and keeps tracking on its own, even if the phone sleeps.

Compass that really works

Motors, battery and electronics ride on the turret, so the app can spin it, fit the magnetometer readings and subtract the motors' field.

Tap-to-sync alignment

LEVEL, NORTH, then SYNC: tap the star on the camera image to refine the alignment to about 0.1–0.2° (design estimate).

Laser with hardware interlocks

A key switch and a horizon cam switch in series with the relay cut laser power below 20°; firmware adds a 30° limit and hold-to-fire.

Built-in sky catalogue

892 stars to magnitude 4.5, 123 deep-sky objects with the Messier list and southern showpieces, plus the Sun, Moon and planets.

Unlimited azimuth

No cables cross the rotating joint: a USB-C PD power bank rides on the turret, so there is no slip ring and no cable wrap.

What you will learn

  • Celestial coordinates: RA/Dec, alt/az and sidereal time
  • Precession, proper motion and atmospheric refraction
  • Positions of the Sun, Moon and planets
  • A six-term mount model: IA, IE, CA, NPAE, T0, T90
  • Alignment with gravity, a compass spin fit and star sync
  • Stepper belt drives and a 50 Hz tracking loop
  • Laser safety: hardware interlocks and a dead-man switch
  • A BLE text protocol between phone and controller

Three ways to get it

Be the first to build the Star Tracker

This kit is still in development. Leave your contact and we will write to you when it is released.

DIY: files and software

The whole build is yours: print the parts, buy the components, build the electronics and assemble the machine.

You do
Print, source the components, build the boards, assemble
  • Print files of every part (STL, STEP and 3MF)
  • Electronics design: wiring, schematics and the list of components
  • Firmware and software, including the app when the kit has one
  • Assembly manual
Notify me

Kit: electronics ready

The hard part comes done: every component, with the electronics assembled and tested. You print the parts and put the machine together.

You do
Print the parts and assemble
  • Everything in the DIY option
  • Every component on the bill of materials: electronics, cables and hardware
  • Electronics assembled and tested, ready to connect
  • Filament not included: you print the parts
Notify me

Ready to use

Printed, assembled and tested by us. Install the software and start using it.

You do
Install the software and use it
  • The complete machine, printed and assembled
  • Tested before it leaves the workshop
  • Firmware installed; app, manual and files included
Notify me

Price on request: it depends on the option. In the DIY option the filament, the electronics and the hardware are yours to source (this page lists them); in the kit option, only the filament.

Included with every option

The files, the manual and the software come with every option, the ready-to-use machine too.

Print files

  • STL files for every printed part
  • Five two-colour 3MF armor plates with the mech livery
  • STEP assembly and STEP parts for CAD
  • Firmware for the M5Stack CoreS3

Assembly manual

  • Build guide: base, turret, fork, cradle and drives, armor, laser, first power-up
  • Bill of materials and the wiring diagram
  • Pointing and alignment theory: astronomy pipeline, mount model, error budget
  • Laser safety guide for the operator, with the hardware and firmware interlocks

App

ST-01 Sky Android

  • SKY: camera view with the reticle, labelled sky, target card and off-screen arrow
  • TARGETS: tonight's best, Solar System, stars, deep-sky objects and search
  • ALIGN: GPS and time, LEVEL, NORTH compass spin fit and SYNC by tap
  • MOUNT: scan and connect over BLE, state, settings and log
  • LASER panel: locks, arm and hold-to-fire, with a first-use safety screen
  • Hand-held sky viewer without the mount, and an all-red night mode