Creative machines

3DEngraver

Emboss paper with roller sleeves you print from any picture

EG-01 is a motor-driven rotary embosser for paper and card up to A4. Its 3D-printed male and female roller sleeves swap like cartridges, and RollerStudio or RollerMobile turns any picture into a new sleeve set ready to print.

  • In development
  • Level: Advanced
  • Version: 0.1.0

v0.1.0 first design: unit-tested and simulated, not built yet. Forces and results are estimates.

The experience

You print the frame, the gears and a sample sleeve set, fit the ground steel axles and bearings, wire the M5Stack units and flash the CoreS3. Open a picture in RollerStudio or on your phone, adjust the trace, place it once or tile it round the roller, and export the male and female sleeves as watertight STL files. Drop the set between the hubs, write its NFC tag, tap it on the TAP ROLLER reticle and press the key: the sheet goes in flat and is designed to come out embossed. You learn rolling geometry, gear registration, force sensing and mesh generation. First design: unit-tested and simulated, not built yet.

What makes it special

Swappable sleeve cartridges

Pull the tailstock knobs and lift the set out. Dog pins of two sizes make the sleeves fit one way only, so male and female stay in register.

Any picture, any pattern

Trace a PNG or JPG, place it once or tile it seamlessly round the roller, set the relief and paper thickness, then export STL or 3MF.

Watertight sleeves, always

A purpose-built mesher wraps the design onto the cylinder: every exported STL is closed and manifold, checked before it is written.

NFC roller tag

The apps write the name, relief, paper and force hint to a tag in the sleeve. Tap it and EG-01 shows the installed pattern on its screen.

Measured embossing force

Two load cells in the pressure screws show the left/right balance on the HUD and stop the rollers on overload (≤ 400 N per side).

AUTO sheet registration

In AUTO, EG-01 waits for a sheet, places the design at the same distance from the leading edge every time, counts sheets and stops on a jam.

What you will learn

  • Rolling geometry: one design mapped onto male and female sleeves
  • Gear trains and registration with 1 : 1 sync gears
  • Image tracing: threshold, despeckle, Bézier curve fitting
  • Watertight mesh generation on a cylinder
  • Force sensing with load cells and overload protection
  • State machines: MANUAL and AUTO modes, interlocks, jam detection
  • NFC tags as the link between the apps and the machine

Three ways to get it

Be the first to build the 3DEngraver

This kit is still in development. Leave your contact and we will write to you when it is released.

DIY: files and software

The whole build is yours: print the parts, buy the components, build the electronics and assemble the machine.

You do
Print, source the components, build the boards, assemble
  • Print files of every part (STL, STEP and 3MF)
  • Electronics design: wiring, schematics and the list of components
  • Firmware and software, including the app when the kit has one
  • Assembly manual
Notify me

Kit: electronics ready

The hard part comes done: every component, with the electronics assembled and tested. You print the parts and put the machine together.

You do
Print the parts and assemble
  • Everything in the DIY option
  • Every component on the bill of materials: electronics, cables and hardware
  • Electronics assembled and tested, ready to connect
  • Filament not included: you print the parts
Notify me

Ready to use

Printed, assembled and tested by us. Install the software and start using it.

You do
Install the software and use it
  • The complete machine, printed and assembled
  • Tested before it leaves the workshop
  • Firmware installed; app, manual and files included
Notify me

Price on request: it depends on the option. In the DIY option the filament, the electronics and the hardware are yours to source (this page lists them); in the kit option, only the filament.

Included with every option

The files, the manual and the software come with every option, the ready-to-use machine too.

Print files

  • STL files for all 42 printed parts
  • Five two-colour 3MF plates with the mech livery
  • STEP assembly and STEP parts for CAD
  • Three sample sleeve sets ready to print: EMBLEM, HEXGRID, CHEVRON
  • Firmware for the M5Stack CoreS3

Assembly manual

  • Build guide: frame, gear train, tailstock, pressure screws, setting the gap
  • Bill of materials with the reason for every bought part
  • Wiring diagram, parts and address plan for the M5Stack units
  • Pattern guide: pictures, sizes, tiles and printing the sleeves
  • Safety notes and first-run checks

App

RollerStudio / RollerMobile Windows Android

  • Trace a picture: threshold, invert, blur, despeckle, Bézier fit
  • Place it once or as a seamless tile; set relief, paper and pair kind
  • Lit preview of the embossed sheet and a 3D view of the sleeve set
  • Export STL, 3MF, the tag record and an .eg01 project
  • Write and read the roller's NFC tag
  • RollerStudio MACHINE tab: USB console with status, RUN/STOP, modes, jog, speed and tare