Control & robotics

Two-Wheeled Robot

The inverted pendulum you can take for a walk

A two-wheeled robot that balances by itself, built to learn how a Segway or a hoverboard works. It is designed to stand up from its stand, hold its place when pushed and drive over Wi-Fi, with a Windows app that tunes it, simulates it and carries the theory course.

  • In development
  • Level: Intermediate
  • Version: 0.1.0

Design v0.1.0: simulated and checked in CAD; the first unit is not built yet

The experience

Run BalanceStudio in SIMULATOR mode first: the robot stands up from its stand, you drive it with WASD, push it, switch PID ↔ LQR and move the battery, all on a copy of the robot's own control code. Then print the frame, the wheels with TPU tyres and the armor plates, mount two NEMA 17 steppers back to back and stack the M5Stack CoreS3 on its driver. Press START and the robot is designed to lift itself off its ±15° stand, balance at 400 Hz and hold its position when pushed; join its Wi-Fi access point and drive it from the keyboard, a joystick or a gamepad. Every gain is live, the charts show each controller term, and the LEARN tab holds the ten-chapter course, offline.

What makes it special

Stands up by itself

It rests at ±15° on a front or back stand. On START a burst under the lean lifts it, then the balance controller takes over.

Two controllers, live

A cascaded PID (position, speed, tilt) and an LQR state feedback, switchable on the fly. The default PID gains are the LQR law in cascade form.

PC-free control loop

The 400 Hz loop runs on the CoreS3. Wi-Fi carries references, parameters and telemetry; if the link drops, the robot stops and holds its position.

Simulator with real code

BalanceStudio simulates the nonlinear robot, with stands, falls and IMU noise, on a line-by-line copy of the robot's C++ control code.

Move the battery

The battery drawer has three heights. The centre of mass moves, yet the unstable pole barely does (5.97 → 5.93 rad/s, CAD model). Find out why.

Course inside the app

The LEARN tab renders the ten theory chapters and the guides with equations and diagrams, offline.

What you will learn

  • Modelling the robot with Lagrange
  • IMU sensing and the complementary filter
  • PID on the tilt loop, anti-windup, delay and noise
  • Cascade control and lean back to brake
  • State space, LQR and choosing Q and R
  • Stepper drive: microstepping, torque and step loss
  • Differential drive, steering and odometry
  • Wireless telemetry and how a hoverboard does it

Three ways to get it

Be the first to build the Two-Wheeled Robot

This kit is still in development. Leave your contact and we will write to you when it is released.

DIY: files and software

The whole build is yours: print the parts, buy the components, build the electronics and assemble the machine.

You do
Print, source the components, build the boards, assemble
  • Print files of every part (STL, STEP and 3MF)
  • Electronics design: wiring, schematics and the list of components
  • Firmware and software, including the app when the kit has one
  • Assembly manual
Notify me

Kit: electronics ready

The hard part comes done: every component, with the electronics assembled and tested. You print the parts and put the machine together.

You do
Print the parts and assemble
  • Everything in the DIY option
  • Every component on the bill of materials: electronics, cables and hardware
  • Electronics assembled and tested, ready to connect
  • Filament not included: you print the parts
Notify me

Ready to use

Printed, assembled and tested by us. Install the software and start using it.

You do
Install the software and use it
  • The complete machine, printed and assembled
  • Tested before it leaves the workshop
  • Firmware installed; app, manual and files included
Notify me

Price on request: it depends on the option. In the DIY option the filament, the electronics and the hardware are yours to source (this page lists them); in the kit option, only the filament.

Included with every option

The files, the manual and the software come with every option, the ready-to-use machine too.

Print files

  • STL files for every printed part, TPU tyres included
  • Two-colour 3MF armor plates with the yellow mech livery
  • STEP files of the assembly and of each part
  • Firmware for the M5Stack CoreS3

Assembly manual

  • Build guide with every part, fastener and step
  • Bill of materials and wiring diagram
  • Tuning guide and lab experiments
  • Drive study: why steppers move the wheels
  • Safety notes and first power-up checklist

App

BalanceStudio Windows

  • Finds the robot over Wi-Fi and drives it with the keyboard, an on-screen joystick or a gamepad
  • Live charts of tilt, speed, position, command and controller terms
  • Parameter editor and LQR designer with the battery position
  • Simulator running a copy of the robot's control code
  • Experiments with metrics and CSV recording
  • LEARN tab: the whole theory course, offline