Control & robotics

Ball on Plate

A camera, three steppers and a plate with no wall to save the ball

A ball-on-plate balancer with vision in the loop. A camera on a mast finds an orange ball and three steppers tilt a plate with no wall to bring it to the centre, to a point you click or along a path you draw, with a Windows app that explains every controller term.

  • In development
  • Level: Advanced
  • Version: 0.1.0

Design v0.1.0: simulated and checked in CAD; the first unit is not built yet

The experience

Open PlateStudio and press SIMULATOR: a plate model, a synthetic camera and a port of the firmware let you drag gains, draw a path and even practise the camera calibration before printing. Then print all 28 made parts, fit three NEMA 17 steppers under the octagonal plate and mount the AtomS3R-M12 camera 300 mm above it. After homing, camera calibration and LEVEL CAL, you put the ball on the plate and press START: the design brings it to the centre and keeps it there when you push it, on a plate that is flat to its edge. Switch PID ↔ LQR and Kalman ↔ raw camera, turn feedforward off, run the identification experiment and see on the image what each term is asking the plate to do.

What makes it special

No wall

The plate is flat to its edge: the controller, not a rim, keeps the ball on. In simulation the defaults catch a 0.4 m/s flick from the centre.

Vision on board

An AtomS3R-M12 finds the ball in every frame and sends its pixel position to the controller over a Grove cable. The PC stays out of the loop.

Latency made visible

Each measurement carries its age and a Kalman filter fuses it at the time it was taken. Switch to raw camera to see what the delay does.

3-RRS direct drive

Three direct-drive steppers on a 3-RRS parallel mechanism: no backlash, no servo deadband, 0.03° resolution, tilt and height control.

Draw your own path

Circle, figure-8, square, click-to-go or a path you draw with the mouse. Turn feedforward off and watch the tracking error grow.

The app explains

Arrows on the camera image show what the P, I, D and feedforward terms ask of the plate at this instant; the charts stack them over time.

What you will learn

  • Ball-on-plate dynamics: the rolling sphere
  • PID on a double integrator, delay and phase margin
  • Kalman filtering and latency compensation
  • State feedback and discrete LQR
  • Kinematics of the 3-RRS parallel mechanism
  • Camera calibration: distortion, homography, parallax
  • Trajectories and feedforward
  • Identification and model-based tuning

Three ways to get it

Be the first to build the Ball on Plate

This kit is still in development. Leave your contact and we will write to you when it is released.

DIY: files and software

The whole build is yours: print the parts, buy the components, build the electronics and assemble the machine.

You do
Print, source the components, build the boards, assemble
  • Print files of every part (STL, STEP and 3MF)
  • Electronics design: wiring, schematics and the list of components
  • Firmware and software, including the app when the kit has one
  • Assembly manual
Notify me

Kit: electronics ready

The hard part comes done: every component, with the electronics assembled and tested. You print the parts and put the machine together.

You do
Print the parts and assemble
  • Everything in the DIY option
  • Every component on the bill of materials: electronics, cables and hardware
  • Electronics assembled and tested, ready to connect
  • Filament not included: you print the parts
Notify me

Ready to use

Printed, assembled and tested by us. Install the software and start using it.

You do
Install the software and use it
  • The complete machine, printed and assembled
  • Tested before it leaves the workshop
  • Firmware installed; app, manual and files included
Notify me

Price on request: it depends on the option. In the DIY option the filament, the electronics and the hardware are yours to source (this page lists them); in the kit option, only the filament.

Included with every option

The files, the manual and the software come with every option, the ready-to-use machine too.

Print files

  • STL files for every printed part
  • Two-colour 3MF for the plate, with its calibration markers, and the armor plates
  • STEP files of the assembly and of each part
  • Firmware for the CoreS3 controller and for the AtomS3R-M12 camera

Assembly manual

  • Build guide with every part, fastener and step, plus safety notes
  • Bill of materials and wiring diagram
  • Calibration guide: homing, camera calibration and LEVEL CAL
  • Tuning guide and 16 lab experiments
  • Theory course in 9 chapters

App

PlateStudio Windows

  • Camera image with the measurement, estimate, setpoint and P/I/D/FF arrows, plus a 3D twin
  • Live charts of every signal and controller term, XY trace and phase portrait
  • Parameter editor with step-response and pole preview, and an LQR designer
  • Trajectories, experiments with model fit, and a metrics table to compare runs
  • Camera calibration wizard with 13 markers and residuals
  • Simulator with a synthetic camera, a manual game mode and CSV recording