Electronics & IoT

Dice Tester

Launch a die, read it with a camera, repeat for hours

An automatic dice-rolling rig: a 24 V coil launches a die of about 10 g up a square acrylic tube, and a camera at the top reads the result. It sits on a sealed enclosure with armor plates and yellow DT-01 mech livery. Designed, not built yet.

  • In development
  • Level: Advanced
  • Version: v16

Mechanics v16 checked in CAD; box not printed, board not manufactured, firmware not written

The experience

You print 19 files: a sealed graphite box, four white armor plates with the yellow DT-01 livery inlaid in two-colour 3MF, the launch tower and the corner posts of a square tube closed by four 3 mm acrylic plates. You wind the coil, solder one board that joins the 24 V input, the coil driver and a plug-in M5Stack AtomS3 Lite, and seat an AtomS3R-M12 camera at the top of the tube. The project is at mechanics v16: checked in CAD, with the box not printed, the board not manufactured and the firmware not written yet. It is a build for people who want to learn coil launchers, pulse drivers, thermal protection and machine vision from the inside, and who are ready to write the firmware themselves.

What makes it special

Coil launcher

An air-core coil pulls a steel projectile that strikes a TPU floor and throws the die up the tube. The wound coil measured ≈ 1.82 Ω.

Mech armor plates

Graphite body, four white armor plates and yellow DT-01 livery inlaid 0.6 mm, exported as two-colour 3MF.

Sealed air path

The box is modelled so that air enters only through the 60 mm fan and leaves only through the tower, passing over the coil.

Camera on top

An M5Stack AtomS3R-M12 sits in a socket at the top of the tube, with an Atomic TF base to store the images on a microSD card.

One custom board

A 144.5 × 55 mm KiCad 8 board joins the supply, the coil driver and the AtomS3 Lite. ERC and DRC report 0 violations.

Thermal protection rules

The specified logic blocks launches at 70 °C and whenever there is no valid temperature reading for more than 15 s.

What you will learn

  • How an air-core coil accelerates a steel projectile
  • Driving a coil with short pulses of about 12 A
  • Measuring the resistance and inductance of a wound coil
  • Thermal protection with a DS18B20 and a thermal fuse
  • Two-layer PCB design in KiCad 8, with ERC and DRC
  • Parametric CAD in CadQuery with interference checks
  • Two-colour inlay printing on a multi-material printer

Three ways to get it

Be the first to build the Dice Tester

This kit is still in development. Leave your contact and we will write to you when it is released.

DIY: files and software

The whole build is yours: print the parts, buy the components, build the electronics and assemble the machine.

You do
Print, source the components, build the boards, assemble
  • Print files of every part (STL, STEP and 3MF)
  • Electronics design: wiring, schematics and the list of components
  • Firmware and software, including the app when the kit has one
  • Assembly manual
Notify me

Kit: electronics ready

The hard part comes done: every component, with the electronics assembled and tested. You print the parts and put the machine together.

You do
Print the parts and assemble
  • Everything in the DIY option
  • Every component on the bill of materials: electronics, cables and hardware
  • Electronics assembled and tested, ready to connect
  • Filament not included: you print the parts
Notify me

Ready to use

Printed, assembled and tested by us. Install the software and start using it.

You do
Install the software and use it
  • The complete machine, printed and assembled
  • Tested before it leaves the workshop
  • Firmware installed; app, manual and files included
Notify me

Price on request: it depends on the option. In the DIY option the filament, the electronics and the hardware are yours to source (this page lists them); in the kit option, only the filament.

Included with every option

The files, the manual and the software come with every option, the ready-to-use machine too.

Print files

  • 19 print files: 14 STL and 5 two-colour 3MF (the box and the four armor plates)
  • STEP files of the main parts and of the full assembly
  • Test pieces to choose the acrylic slot width before printing the long corner posts
  • Single board v2 fabrication files: Gerbers, drill files and SMD positions

Assembly manual

  • Mechanical guide: parts table with material and orientation, hardware list and assembly steps (currently in Portuguese)
  • Board schematic in PDF, BOM and shopping list
  • Wiring of the two Atom controllers, pin by pin
  • Coil and launcher notes: design values, measurements and thermal safety
  • Open items and the test plan still to be run

App

This kit works without an app.