Electronics & IoT

Outage Alarm

The buzzer that sounds the moment your wall outlet goes dead

A fail-safe power outage alarm with no microcontroller and no firmware: a relay, a TP4056 charger, an 18650 cell and a buzzer in a three-part printed wedge with mech livery. When the 5 V from the wall disappears, it sounds.

  • In development
  • Level: Beginner
  • Version: 1.0.0

v1.0.0 print files and docs are published; the enclosure has not been test-printed yet

The experience

You print three parts without supports: the tilted control face, the walls and a dark base. With a multi-material printer, the mech livery (unit code OA-01, a reticle and hazard stripes) is inlaid flush in a second filament, all of it in the first 3 layers of the top. Then you cut one perfboard using the 1:1 template, solder a relay, a diode and a resistor, and wire the TEST button, the ARM switch, the POWER LED and the buzzer. Four hidden screws close the case and clamp the board. Plug a USB charger into the wall, hold TEST, and the buzzer answers. Along the way you learn why a normally closed relay contact makes a circuit fail-safe and how a Li-ion cell stays protected and charged.

What makes it special

Fail-safe by design

Any loss of the 5 V sets off the alarm: a power outage, a tripped breaker, a dead charger or a loose cable.

A real TEST button

TEST cuts the relay coil exactly as an outage does, so one press checks the battery, the relay, the switch and the buzzer.

No mains on board

Mains voltage stays inside the certified USB charger. You only handle 5 V and the 3.7 V battery.

Mech livery inlaid

Title band with the unit code OA-01, a reticle and hazard stripes, inlaid 0.6 mm in a second filament. One-colour STLs are included too.

One board, four screws

All the electronics sit on one perfboard, clamped by the same four hidden screws that close the enclosure from below.

Days of alarm

Estimated run time while sounding is over 100 h on a 2500 mAh cell. On standby, USB keeps the battery full.

What you will learn

  • How a normally closed relay contact makes a circuit fail-safe
  • Li-ion charging and protection with a TP4056 module
  • Sizing a USB supply from coil, LED and charge currents
  • Why a relay coil needs a flyback diode
  • Cutting and soldering a perfboard from a 1:1 template
  • Two-colour inlay printing on a multi-material printer

Three ways to get it

Be the first to build the Outage Alarm

This kit is still in development. Leave your contact and we will write to you when it is released.

DIY: files and software

The whole build is yours: print the parts, buy the components, build the electronics and assemble the machine.

You do
Print, source the components, build the boards, assemble
  • Print files of every part (STL, STEP and 3MF)
  • Electronics design: wiring, schematics and the list of components
  • Firmware and software, including the app when the kit has one
  • Assembly manual
Notify me

Kit: electronics ready

The hard part comes done: every component, with the electronics assembled and tested. You print the parts and put the machine together.

You do
Print the parts and assemble
  • Everything in the DIY option
  • Every component on the bill of materials: electronics, cables and hardware
  • Electronics assembled and tested, ready to connect
  • Filament not included: you print the parts
Notify me

Ready to use

Printed, assembled and tested by us. Install the software and start using it.

You do
Install the software and use it
  • The complete machine, printed and assembled
  • Tested before it leaves the workshop
  • Firmware installed; app, manual and files included
Notify me

Price on request: it depends on the option. In the DIY option the filament, the electronics and the hardware are yours to source (this page lists them); in the kit option, only the filament.

Included with every option

The files, the manual and the software come with every option, the ready-to-use machine too.

Print files

  • One-colour STLs for the top, the sides and the base, with the labels engraved
  • Two-colour 3MFs for the top and the sides, with the mech livery inlaid
  • Print orientation already set in every file; no supports needed
  • Parametric OpenSCAD source of the enclosure

Assembly manual

  • Printing and assembly guide: settings per part, gluing the top, mounting each component
  • Bill of materials with part references
  • Schematic, wiring table and circuit calculations
  • Perfboard layout drawn 1:1 on A4, usable as a cutting and drilling template
  • Bench test steps and a troubleshooting table

App

This kit works without an app.