3D printing workshop

Filament Recycler

Three desktop machines to turn failed prints and PET bottles into filament

A line of three independent desktop machines: FR-01 shreds failed prints into flakes, FR-03 cuts PET bottles into strip, and FR-02 is designed to turn either into 1.75 mm filament on a 1 kg spool. Build one, two or all three.

  • In development
  • Level: Advanced
  • Version: 0.2.0

v0.2 design only: modelled and checked in CAD. Not built or tested, no firmware yet; figures are estimates.

The experience

You choose a machine and print most of it in PETG on a 220 × 220 mm bed, including white armor plates with yellow mech livery. Then comes real machine building: a dual-shaft cutting box with steel blades, an auger extruder with three heater zones, a puller, a traverse and a winder on a 2020 frame, or a gravity-fed bottle cutter. You wire a 24 V system around an E-stop latch that works without software. You learn why some parts must stay metal, how filament diameter is controlled, and how PET strip is formed in a hot die. This is a design-stage release: fully modelled and checked in CAD, not built or tested yet, and the firmware is still to come.

What makes it special

FR-01 Shredder

Dual-shaft shredder with 2 × 10 hooked blades, a 24 V 250 W worm gearmotor and a printed sieve, designed to make flakes up to 5 mm.

FR-02 Extruder

Filament line with a 16 mm auger, 3 heater zones, air cooling, a hall-effect diameter sensor, puller, traverse and winder for 1 kg spools.

FR-03 Bottle Cutter

A cutter head rides on the bottle edge by its own weight and a utility-knife blade cuts a strip 6–12 mm wide, wound on a 1 kg spool.

Independent modules

Each machine has its own power supply, controller, E-stop and documentation. They connect only through the material: flakes or PET strip.

A stop without software

The E-stop (and the FR-01 lid) breaks a two-relay latch that feeds every actuator. The microcontroller can open the latch but never close it.

Printed first, mech livery

Metal only where a part cuts, carries drive loads or gets hot. White armor plates carry yellow mech markings inlaid 0.6 mm.

What you will learn

  • How a dual-shaft shredder cuts: blades, combs and sieve
  • Screw extrusion: auger, barrel, heater zones and die
  • Filament diameter control with a sensor and a puller
  • Forming PET bottle strip into filament in a hot die
  • Deciding which parts are printed and which stay metal
  • E-stop safety latches that do not depend on firmware
  • Traverse winding of filament and strip on a spool
  • Two-colour printing with inlaid livery

Three ways to get it

Be the first to build the Filament Recycler

This kit is still in development. Leave your contact and we will write to you when it is released.

DIY: files and software

The whole build is yours: print the parts, buy the components, build the electronics and assemble the machine.

You do
Print, source the components, build the boards, assemble
  • Print files of every part (STL, STEP and 3MF)
  • Electronics design: wiring, schematics and the list of components
  • Firmware and software, including the app when the kit has one
  • Assembly manual
Notify me

Kit: electronics ready

The hard part comes done: every component, with the electronics assembled and tested. You print the parts and put the machine together.

You do
Print the parts and assemble
  • Everything in the DIY option
  • Every component on the bill of materials: electronics, cables and hardware
  • Electronics assembled and tested, ready to connect
  • Filament not included: you print the parts
Notify me

Ready to use

Printed, assembled and tested by us. Install the software and start using it.

You do
Install the software and use it
  • The complete machine, printed and assembled
  • Tested before it leaves the workshop
  • Firmware installed; app, manual and files included
Notify me

Price on request: it depends on the option. In the DIY option the filament, the electronics and the hardware are yours to source (this page lists them); in the kit option, only the filament.

Included with every option

The files, the manual and the software come with every option, the ready-to-use machine too.

Print files

  • STEP assembly of each machine with mechanical and electrical parts, plus one STEP per custom part
  • STL for every printed part in its print orientation, sized for a 220 × 220 mm bed
  • Two-colour 3MF files for the armor plates with the mech livery
  • DXF for the laser-cut steel and aluminium parts of FR-01 and FR-02

Assembly manual

  • A build guide per machine: every part in detail, step-by-step assembly and sourcing of the non-printed parts
  • Mechanical notes: design, printed versus metal parts and why, print settings
  • Electronics: wiring diagram, power, safety chain, pin map and bench bring-up
  • Bill of materials for each machine
  • A safety page per machine with the hazards and the rules

App

This kit works without an app.